NATURAL LAWN CARE GARDENING AGRICULTURE LIVESTOCK WASTE MANAGEMENT WASTE WATER TREATMENT OIL SPILL CLEANUP SEPTIC TANK ADDITIVE MOLD & FUNGUS CONTROL ALGAE CONTROL NATURAL POND CLEANER COMPOSTING ODOR ELIMINATOR PET AREA ODOR CONTROL

EC-601 is a super concentrated, high efficiency, low toxicity bio-surfactant for use in breaking down and dispersing fresh and weathered hydrocarbons. EC-601 contains a class of natural compounds which aid in bringing chemicals, which are not water soluble, into solution. EC-601 is effective in accelerating the process of natural dispersion when mechanical recovery is not feasible and supporting indigenous bacteria and microbial inoculants in ex-situ and in-situ environments. EC-601 has high solubilizing properties and does not adsorb to soil. When compared to chemicals, the efficacy of EC-601 is significantly higher. In addition, EC-601 has a significantly lower impact on the environment. 

EC-601 BENEFITS
• Sludge reduction >50%.
• Hydrocarbon recovery >90% 
• black">Water recovery >90
• Recovered water can be drained directly to containment or WWT.
• Improves sludge setting capacity
• Significantly reduces cleanup time and cost

APPLICATION
Typical dilution rate in water: 50 to 100 PPM.

EC-601 is a multifunctional product. For this reason please contact your EcoChem representative for specific application rates.

TESTING REQUIREMENTS FOR CRUDE OIL SPILLS
The characteristics of crude oils can vary depending upon point of origin and method of extraction. Therefore, it may be necessary to collect several representative samples of the spilled product for laboratory analysis to (1) determine its characteristics and (2) develop the most effective EC-601 application rate.

APPLICATION - CONTAMINATED SOIL
Dilute EC-601 in non-chlorinated water at  rate of 50 to 100 PPM and spray the diluted solution directly onto the affected area. This will (1) separate the oil from the soil (2) reduce the oil to small droplets and (3) accelerate the bioremediation process. EC-601 can also be used to support microbial inoculants and indigenous biomass.

APPLICATION - SUMPS, PITS, CONTAINMENT
EC-601 reduces interfacial tension between the oil, water and inorganics and creates a tri-phase condition within the treatment environment whereby the oil, water and sediments (in-organics) are separated. EC-601 does not bind to soil, sediments etc. and is ideally suited for application where mechanical separation in not feasible.

APPLICATION - SURFACE AND SUBMERGED OIL SLICKS
A part of the surfactant molecule used in EC-601 has an attraction to oil (i.e. it is oleophilic). while another part has an attraction for water (i.e. it is hydrophilic). When EC-601is applied onto an oil slick, the interfacial tension between the oil and water is reduced, resulting in the formation of finely dispersed oil droplets. Typically, these droplets will vary in size and, although the larger ones may rise to the surface, a significant amount will remain in suspension. When dispersion is successful, a characteristic plume will spread slowly downward from the surface shortly after EC-601 is applied. Optimum distribution can be achieved thru mechanical agitation, natural wave action, boat propellers and wakes. To disburse submerged oil slicks, dilute EC-601 at a rate of 100 PPM in water and inject the diluted solution directly into the oil slick. Injection can be carried out with the aid of high pressure pumps and under water lances. As the mass disperses, some large pockets of oil may rise to the surface. When this occurs, an additional application of EC-601 may be required. Effective distribution of EC-601 throughout the oil slick is crucial to the success of the process.

APPLICATION - SHORELINES
EC-601 rhamnolipid biosurfactant dispersants can also be used on shorelines including beaches, rocks, soil and sea walls. Shores lines subjected to strong wave action are cleaned quickly and naturally. Re-application may be necessary in areas where dense hydrocarbon deposits have accumulated. When EC-601 is applied to viscous oils on shorelines, where retention time exceeds 24 hours, dilution rates can be increased. Typical dilution rate in water - 50 to 100 PPM.

PACKAGING
1 Litre HDPE Jugs
4 Litre HDPE Jugs
20 Litre HDPE Pails

SAFETY
The materials used in the production of EC-601 are derived from naturally occurring and sustainable sources. EC-601 is environmentally friendly, biodegradable and is not harmful to animals, plants and humans.

COMPLIANCE
Fully complies with EPA Toxic Substance Control Act (TSCA) and the rules, orders and regulations promulgated there under including:
a) Sections 4, 5, 6 & 7; Title 40 Chapter 1, 707.20 thru 707.75;
b) 40 CFR Sections 704.3. 710.2(e) and 720.3(c); and
c) Sections 5 and 13, reference 42FR64583
d) Does not contain marine pollutants as defined in 49 CFR 171.8. 

STORAGE & HANDLING
DO NOT FREEZE! Store in a cool dry location. (See MSDS)

ENVIRONMENTAL CLEANUP

EC-601 CASE STUDIES

OIL SPILL CLEANUP INFO